Wedge Anchor Introduction
"Wedge Anchor" is a generic term for a type of anchor used to fasten a variety of materials to concrete. Some companies have different brand names for their wedge anchors such as Kwik Bolt, Power Stud and Thunderstud. The different brands of wedge anchors all work on the same principles, are made from the same basic materials, and provide similar high quality performance.
What is a Wedge Anchor?
Wedge anchors consist of two separate pieces that are permanently pre-assembled into a single unit. The first piece is a carbon steel rod that is threaded for a portion of its length. The opposite end, the installed end of the anchor, has a necked-down diameter, or conical space, that tapers outward back to the rod's full diameter.
The second piece of the wedge anchor is a steel clip, or sleeve, that is permanently assembled around the conical section of the rod. Each wedge anchor also requires a nut and washer to complete installation.
Wedge anchors can be used in numerous applications as long as the base material is solid concrete. Unlike many other concrete fasteners, the wedge anchor cannot be used in brick or block.
The wedge anchor is simple to use and is available in a wide variety of diameters and lengths. Wedge anchors can be used in both light and heavy duty applications. A 1/4" x 1-3/4" wedge anchor, for instance, would be utilized in a light duty application, while a 1-1/4" x 12" anchor would be used in a situation that requires a heavy duty anchor.
How Does a Wedge Anchor Work?
Again, wedge type concrete fasteners are designed for use in solid concrete only. They are designed to go into a pre-drilled hole in concrete. Once installed, these wedge anchors can not be removed without destroying the concrete. The size of the anchor is always equal to the size of the hole that needs to be drilled into the concrete. The tolerance between the hole and the anchor is very tight. As the anchor is hammered into the hole, the clip is recessed in the gap of the conical space, allowing the anchor to penetrate the hole. To set the anchor, the rod must be pulled-up (which occurs while the nut is being tightened), making the clip move outward on the tapered space, wedging itself between the rod and the wall of the hole.
Since the hole tolerance is critical in the performance of the wedge anchor, it is important that the correct drill and drill bits are used. A hammer drill should be used rather than a standard power drill because it creates a better quality hole. A carbide-tipped masonry bit should also be used because they are specifically designed for use in hammer drills and meet ANSI standards.
Wedge Anchor Holding Values
When anchoring into concrete, wedge anchors are an excellent choice because of their holding values. The holding power of the wedge anchor, as with any anchor, is always dependent on the quality of the concrete. As a rule of thumb, a safety factor of 4:1, or 25%, is generally accepted as a safe working load. Holding values are also derived from the depth of the embedment- the deeper the embedment, the better the holding values. The wedge anchor must be embedded into the concrete up to or past the minimum embedment depth to obtain published holding values. It is also essential to ensure that the anchors are not placed too close together or too close to an unsupported edge.
The pressure exerted on the concrete by a wedge anchor can be best described as cone-shaped, with the small end of the cone being the inserted end of the anchor and the large end of the cone being at the surface of the concrete. If two wedge anchors are set too close together, the pressure from the two anchors would intersect, decreasing the holding values of both anchors. These same factors apply when placing an anchor near an unsupported edge. It is possible for the concrete to crumble under pressure if the concrete anchor is placed too close to the unsupported edge.
The general recommendation is that an anchor should be placed no closer than five diameters from any unsupported edge. For example, a 1/2" diameter anchor should be at least 2-1/2" from any unsupported edge of concrete. Also, two anchors should never be set less than ten diameters from each other. That is, two 1/2" diameter wedge anchors should be placed at least 5" apart.
Determining the Correct Size Wedge Anchor to Use
The diameter of the wedge anchor required for an application usually depends on the size of the hole in the fixture to be fastened. The "fixture" could be anything from a 2x4 to a piece of angle iron, bracket or steel plate. The hole size in the fixture is most often determined by an engineer based on the necessary holding values for each particular application. It is imperative to ensure that the concrete wedge anchor fits through the hole in the fixture. A 1/2" wedge anchor is, in reality, slightly larger than 1/2".
Each wedge anchor diameter is available in a variety of lengths. The length required needs to be determined for each application and is dependent upon the thickness of the fixture to be fastened, plus the minimum embedment. To determine the length of anchor needed, simply add the thickness of the fixture to be fastened to the minimum embedment for the wedge anchor diameter being used, plus the thickness of the nut and washer (typically the diameter of the anchor is close to the thickness of the nut and washer).
This will give you the minimum length of anchor required. Using a longer wedge anchor than necessary will increase the holding values, but may increase your risk of drilling into rebar embedded in the concrete.
Wedge Anchor Installation
The installation of the concrete wedge anchor can be completed by following the steps below:
1. Determine the correct length of wedge anchor required to ensure that the minimum embedment is met and ensure that the wedge anchor fits through the hole in the fixture. The washer should also be larger than the fixture hole.
2. Using the hole in the fixture as a template, carefully drill your holes using a hammer drill and carbide-tipped masonry bit. The drill bit diameter should be the same as the ลิ่มยึดของเส้นผ่าศูนย์กลาง มันมีความจำเป็นที่หลุมถูกล้างของฝุ่นละอองและเศษซาก ซึ่งสามารถทำได้โดยใช้แปรงลวดอัดอากาศหรือสูญญากาศ
3 วางเครื่องซักผ้าและถั่วที่ยึดน๊อเปิดกี่รอบ ไม่เต็มเกลียวน๊อปกป้องกระทู้ของลิ่มยึดเมื่อตอกเข้าไปในช่อง
4 แทรกตอกยึดเข้าไปในช่องรูในตารางการแข่งขัน
5 อย่างรอบคอบค้อนสมอลงในแต่ละหลุมให้มั่นใจว่ากระทู้ไปด้านล่างติดตั้งพื้นผิวของคอนกรีตหรือที่ผ่านมาของขอบและที่ embedment ต่ำสุดคือได้พบกับ
6 ขันน็อต -- นิ้วมือแน่น ใช้ประแจเพื่อขันน็อต 3 หรือ 4 จะเปลี่ยนหรือใช้แรงบิด
ประแจเพื่อให้แน่ใจว่าพวกเขาจะถูกทำให้รัดกุมค่าแรงบิดที่จำเป็น ไม่เกินแรงบิด, เป็น
สมอทั้งจะหมุนอยู่ในหลุมหรือดึงออกจากหลุม
โปรดดูลิ่มนี้สมอวิดีโอการติดตั้ง
Wedge Anchor แรงบิดค่านิยม
แองเคอลิ่มต้องการแรงบิดขั้นต่ำในการตั้งค่า ไม่ต้องขันน็อตเป็นแน่นที่สุดเท่าที่ทำได้ เมื่อตั้งค่าตอกยึดเป็นสิ่งสำคัญที่น็อตเท่านั้นเมาบนนิ้วแน่น เส้นผ่านศูนย์กลางแต่ละจุดยึดมีค่าแรงบิดที่จำเป็นในการที่จะต้องทำให้รัดกุม
Chart ประจำตัวยาว
เมื่อยึดถูกตั้งค่าอย่างถูกต้องสิ่งที่อยู่ข้างต้นยื่นออกมาเป็นรูปธรรมคือถั่วเครื่องซักผ้าและกระทู้ส่วนของ เส้นผ่าศูนย์กลางของฝังสมอได้อย่างง่ายดายเพียงแค่กำหนดโดยการวัดสตั๊ด ความยาวของสมอ แต่สามารถยากที่จะกำหนดความลึกของ embedment เพราะอาจไม่เป็นที่รู้จัก เพื่อช่วยระบุความยาวของการติดตั้งจุดยึด, รหัสประจำตัวประชาชนได้รับการพัฒนา จดหมายจะประทับอยู่ที่ปลายของส่วนเกลียวของลิ่มยึดเพื่อให้ง่ายต่อการกำหนดความยาวของตอกยึดหลังการติดตั้ง จดหมายนี้จะสอดคล้องกับความยาวโดยรวมของจุดยึด (เป็นนิ้ว)
ลิ่มAnchor คุณสมบัติของวัสดุ
คอนกรีตแองเคอลิ่มมีอยู่ในประเภทที่แตกต่างกันของเหล็กและการชุบที่แตกต่างกัน ชนิดของเหล็กและการชุบที่จะใช้จะขึ้นอยู่กับสภาพแวดล้อมของโปรแกรมประยุกต์ เหล็กกล้าคาร์บอนชุบสังกะสี - แองเคอลิ่มถูกใช้ในการใช้งานภายในที่กัดกร่อนไม่มากของปัจจัย ยึด, Nut, เครื่องซักผ้าและคลิปจะทำทั้งหมดของเหล็กกล้าคาร์บอนชุบสังกะสี ประเภทของการชุบนี้จะไม่แนะนำให้ใช้ใน ACQ รับการรักษาไม้แปรรูป
ชุบสังกะสีตอกสมอมีความเหมาะสมสำหรับการใช้งานภายนอกที่มีการกัดกร่อนจากน้ำหรือความชื้นเป็นกังวล สมอ, ถั่ว, และเครื่องซักผ้าจะทำทั้งหมดของเหล็กคาร์บอนและชุบสังกะสี คลิปทำจากสแตนเลส 303 ชุบสังกะสีตอกสมอเป็นที่ยอมรับเพื่อใช้ในการ ACQ ไม้อบ
แองเคอลิ่มมีการผลิตยังอยู่ในสองเกรดของสแตนเลส 303 สแตนเลสมีลักษณะการกัดกร่อนที่ดีเยี่ยมสำหรับภายนอกการใช้งานและสามารถทนต่อสารเคมีอินทรีย์และอนินทรีมาก แต่ไม่ควรใช้ในสภาพแวดล้อมของน้ำทะเล ยึดทำจากสแตนเลส 303 และถั่ว, เครื่องซักผ้าและคลิปที่ทำจากสแตนเลส 18-8 ซึ่งเทียบได้กับ 303 สแตนเลส
316 ชุดสแตนเลสมีความต้านทานการกัดกร่อนที่ดีที่สุดและเป็นปกติจะใช้ในสภาพแวดล้อมรุนแรง 316 จุดยึดสแตนเลสยังสามารถใช้ในสภาพแวดล้อมที่น้ำทะเล ทั้งหมดขององค์ประกอบใน316 stainless steel wedge anchor are made from this resilient 316 steel.
Overview
Wedge anchors are an excellent choice when anchoring into solid concrete. These anchors have excellent holding values and are available in a range of materials and plating to meet the requirements of many applications. It is important to make certain that the correct diameter and length are used in each application to ensure that the wedge anchor is set properly and safely.
Thanks To : Rings Jewelry play station game Civil Engineer Work Plan of Construction Tablet16GBWifiMB292LL
ไม่มีความคิดเห็น:
แสดงความคิดเห็น